Material Safety Data Sheets Multibond 2025. Pro Glue.

Veneer Bond Liquid Resin	Veneer Bond Dry Resin	Veneer Bond Hardener	Veneer Softeneer
High Performance PVA

MSDS: High Performance PVA

Read and understand this before using or handling product.
For emergency purposes: PRO-GLUE, a product line of VAC-U-CLAMP

PRO-GLUE Emergency phone: 888-342-8262
Product Type: PVA/ Adhesive
General product use: Adhesive

CHEMICAL HAZARD RATING
Health=2 (moderate) Fire=2 (moderate) Reactivity=0 (least)

1. Hazardous Ingredients
Product contains no hazardous ingredients or they are below reportable levels.

OSHA PELs & ACGIH TLVs are listed in Section 8 where applicable.

2. Physical Data

EMERGENCY OVERVIEW:
Cream colored water-based adhesive. Slippery in the wet state.

Form:                        LIQUID
Appearance/Color:            CREAM
Odor:                        MILD
Solubility (in water):       SOLUBLE IN WATER
pH Value:                    3.
Boiling Range/Point:         210.øF
Evaporation Rate:            Slower than n-Butyl Acetate

% Volatile:                  49.%
Specific Gravity:            1.11
VOC:                         0.037 LBS/GAL

ROUTES OF ENTRY:
INHALATION: Yes
SKIN: No
EYE: Yes
INGESTION: Yes
INHALATION:
Vapors and/or aerosols which may be formed at elevated temperature may
be irritating to eyes and respiratory tract.
No reported incidents of adverse health affects resulting from
inhalation of vapors at room temperature.
SKIN:
Prolonged or repeated skin contact can cause irritation.
EYE:
Substance may cause moderate eye irritation.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:
Preexisting skin and respiratory conditions.
CARCINOGENICITY:
IARC: No
NTP: No
OSHA:   No
REPRODUCTIVE TOXICITY:
This product has not been evaluated for reproductive toxicity.
TARGET ORGANS:
Eyes and skin.

INHALATION:
Remove patient to fresh air, if discomfort persists seek medical
attention.
INGESTION:
Call poison control center immediately. Follow their specific
instructions.
SKIN:
Wash with soap and water. Contact a physician if irritation develops
or persists.
EYE:
Hold eyelids apart and flush with plenty of water for at least 15
minutes. Seek medical attention.

5. Fire and Explosion Hazards
Flammability Class (OSHA)    IIIB
Flash Point:                 Not Applicable
Explosive Range:             Not Applicable

EXTINGUISHING MEDIA:
Use alcohol foam, carbon dioxide, water spray, or ABC dry chemical
when fighting fires involving this product.
HAZARDOUS COMBUSTION PRODUCTS:
Oxides of carbon.
FIRE FIGHTING PROCEDURES:
Wear a NIOSH approved self-contained breathing apparatus.

6. Safe Handling and Personal Protection
HANDLING:
Empty drums should be completely drained, properly bunged and promptly
returned to a reconditoner, or properly disposed of.
Use only in well ventilated area.
STORAGE:
Store at temperatures between 50 F and 90 F.
PRECAUTIONARY STATEMENT:
For industrial use only.

Normally Stable as defined in NFPA 704-12(4-3.1).
Hazardous polymerization: May occur
Incompatibilities: Strong oxidizers.
Decomposition products may include: none known

Occupational Exposure Limits
           ACGIH TLV     ACGIH TLV-C   ACGIH STEL    OSHA STEL     OSHA PEL

ENGINEERING CONTROLS:
Use local exhaust as needed to maintain occupational exposure limits.
OTHER:
Facilities storing or utilizing any chemical should be equipped with
an eyewash facility and a safety shower.
RESPIRATORY PROTECTION:
Where exposure limits may be exceeded select a NIOSH approved
respirator with appropriate Protection Factor and cartridge for the
specific contaminants. Follow requirements for respiratory protection
in OSHA 1910.134.
EYE PROTECTION:
Chemical splash goggles (ANSI Z87.1 or approved equivalent).
SKIN PROTECTION:
Where skin contact can occur, wear impervious gloves.

9. Spill or Leak and Disposal Procedures
CONTAINMENT TECHNIQUES:
Use inert absorbent to dike the spill. Keep away from drains.

CLEAN-UP:
If possible pump liquid into an approved container or spread absorbent
over spill and shovel product/absorbent mixture into an approved
container. If product has dried scrape up and place in an approved
container.

WASTE DISPOSAL:
Disposal of this product must comply with all applicable federal,
state and local regulations.
CONTAINER DISPOSAL:
Disposal of this container should comply with all applicable federal,
state and local regulations.

10. Stability And Reactivity
Stability: This product is stable
Hazardous Polymerization: Hazardous polymerization will not occur

INCOMPATIBLITY:
Strong acids and bases.
HAZARDOUS DECOMPOSITION PRODUCTS:
Oxides of carbon may be released during combustion.

Acute and chronic health effects are not expected as long as good
industrial hygiene and safety precautions are followed.

UN Number                    NONE
UN Pack Group                N/A
UN Class                     NONHAZ
ICAO/IATA Class              NONHAZARDOUS
IMDG Class                   NONHAZARDOUS
Shipping Name                NONHAZARDOUS

Packaging may not be approved for shipping by air. Please contact
Vac-U-Clamp for further information.

13. Regulatory and other information
TSCA (Toxic Substances Control Act Inventory):
All components of this product are listed on the TSCA inventory except
as exempted.

This formulation has not been tested for environmental effects.

DISCLAIMER:
While the information and recommendations set forth herein are believed to be accurate as of the data hereof, Vac-U-Clamp makes no warranty, express or implied, with respect thereto and disclaims all liability from reliance thereon.

Pro-Glue Wood Products - Order - Cart - Tips from the Master - Pro-Glue Home - Contact Pro-Glue - MSDS Veneer Bond Liquid Resin - MSDS Veneer Bond Dry Resin - MSDS Veneer Bond Hardener - MSDS Veneer Softeneer - Pro-Glue Site Map - Vac-U-Clamp - Admin